Sometimes it happens that the inscription cannot simply be crossed out. It needs to be removed, and as unnoticeably as possible. If with a ballpoint pen everything is more or less simple, then with a gel pen the situation is much more complicated.

Before you erase the gel pen from the paper, it is better to practice. Be patient and use cleaning products.

The easiest way

The method, familiar to many from school, is very simple. However, it requires some skill and caution. It is used if you want to remove a small blemish.

All you need to do is take a sharp razor blade or a hard eraser. Carefully scratch the damaged area, remove paper dust and sand.

Gel ink is much more difficult to erase than regular ink. Therefore, this method can be used if the material is very dense.

Removing ink with vinegar

First, prepare a mixture of acetic acid (1 tsp) and potassium permanganate (a small pinch). Blank thick paper is placed under the already written paper. Use a cotton swab dipped in the solution to gently wet the unwanted recording.

After drying, a pinkish-brownish stain will remain. Don't be afraid. Iron the sheet with a warm iron, first placing it between a soft cloth and a clean sheet on top.

This procedure will help remove gel ink. But you will smell vinegar for a while.

Removing blots with “White”

If you have a question about how to remove marks from a gel pen, you can use the following method:

1. dilute a small amount of “Whiteness” in water;
2. soak a cotton swab in the solution;
3. process the recordings with light blotting movements;
4. let dry.

“Whiteness” is a fairly aggressive agent. You can remove the gel paste practically without traces using this method only from white paper. A yellow or white stain will remain on colored surfaces.

We remove gel ink using improvised means

If there is neither bleach nor potassium permanganate in the house, then you can try to erase the marks using products that everyone has in their kitchen - salt and soda. Substances in equal quantities are poured onto a clean surface in an even layer. Place the damaged sheet on top with the lettering facing down.

It is pressed tightly against the glass in which a hole was previously made. Through this hole, very carefully, using a syringe, apply lemon juice to the ink.

The essence of this method is that the acid eats away traces of gel ink, and soda and salt absorb them. In theory, if you remove a stain this way, there should be no streaks left.

Citric and oxalic acid

To remove traces of gel ink, prepare a solution of 50 ml of water, citric and oxalic acid in the same quantity.

The unnecessary part of the text is treated with a cotton pad or swab until the ink is completely dissolved. It is important not to overdo it or wet the surface too much. Otherwise it will break.

What other ways to remove a gel pen?

In addition to the above means, removing inscriptions and blots made with gel ink is offered by such means as:

• acetone (nail polish remover based on it is also suitable);
• chlorine solution;
• hydrochloric acid;
• a mixture of glycerin and ethyl alcohol.

When using chemicals, it is worth taking into account that these are very aggressive substances and should be used with great care. Under the influence of chemicals, a hole may simply form.

So, in order to erase a gel pen, you need:

• take your time;
• practice on a sheet of similar quality;
• change cotton swabs more often (otherwise there will be stains);
• act very carefully.

However, before you start experimenting, try a method that works great for corrections on white paper. Just apply the corrector and write the correct note on top. In this case, the surface will definitely not look shabby and will not be damaged.

Many in childhood had to think about how to erase a pen from a diary or notebook in order to remove a low grade. It is possible that there were some notes written in ink in the margins of the book. These inscriptions could require quick removal. Removing pen or ink from a sheet of paper is often required by artists who use it for their sketches.

1

You can use conventional chemicals to remove ink. Before removing excess ink, you must keep in mind that this procedure is quite complex. In this case, various methods and means may be required to make the sheet white again.

The stain can be rubbed with a cotton swab dipped in acetone.

Ink is easily removed after using acetone, which is the main component of nail polish removers. The stain can be rubbed with a cotton swab dipped in acetone. Marks from a blue ballpoint pen are easier to erase than black ink marks. Acetone or hydrochloric acid can be used to remove stains from thick paper. Before using them, it is necessary to test the effect of these compounds on unwanted thick sheets.

A fairly strong product is Belizna bleach with a 70-80% active chlorine solution. To remove ink, you can use a mixture of glycerin and ethyl alcohol, taking them in equal proportions. Any chemicals require careful and careful handling. The cotton swabs used should be constantly changed and the brush cleaned.

Medical alcohol (isopropanol) can be successfully used to remove ink marks. Traces of a pen from a damaged sheet can be removed with a cotton swab dipped in the composition. Those areas of the sheet where you want to leave ink should be covered first.

If you need to clear a large sheet of ink, the cotton swab should first be left in medical alcohol for 5 minutes. It is necessary to use a substance that does not contain flavorings or dyes. Isopropyl alcohol can be any brand.

You can remove ink using lemon juice, which you will need to pour a small amount into a cup or glass. A cotton swab is first dipped in the juice and then gently used to remove the ink. When using lemon juice, you must remember that it can corrode leaves, especially thin ones. Ink is easier to remove from thick paper.

To remove ballpoint pen marks, you can use a paste mixture of water and baking soda. To prepare the pasta, you will need a glass bowl. To apply the soda mixture to the sheet, you need a cotton swab.

The paste should be carefully rubbed over the area of ​​the sheet from which traces of ink should be removed. Then the paper must be dried without washing the soda off it. After the moisture evaporates, the soda will begin to fall off. An old toothbrush with stiff bristles will work to remove the ink.

2

Sometimes you need to remove ink from the printer. To do this, you can use a regular blade, which carefully removes the letters. The blade must be held perpendicular to the sheet. You should not press it very hard, otherwise you may tear off the entire sheet.

When choosing what to erase your pen with, you can use a special eraser. Before removing erasable ink, you should carefully examine the packaging. Usually it indicates the color, which should be blue, not black. Manufacturers provide pens for such ink with a special eraser at the end.

You can erase ink using sandpaper

In any case, you should try to erase the pen with an ink eraser. If you use a rubber eraser, it will be difficult for them to remove the ink. This item is designed to remove pencil marks. Be careful when using a vinyl eraser, otherwise you may damage the sheet and not remove the ink from it.

You can erase the ink using sandpaper. For this purpose, you can use fine-grained sandpaper and a small block. It is possible that you need to remove ink from a small area, and the bar is too large.

Before removing the ink from the sheet, you should cut out a small piece of sandpaper and then glue it to the end of the pen where there is no sharpened rod. When removing ink, you must be careful and press hard on the sandpaper. To remove its residue on the sheet, you need to blow lightly.

You can use a fine-grit sharpening stone to remove ink. This will allow you to make a smooth surface treatment of the written sheet than when using sandpaper. Removal can be accomplished with a miniature Dremel sharpening tool that has rounded edges.

You can remove ink marks from the margins of books with a grinding stone, which is ideal for this purpose. If the sheet is not too dense, then the structure of the grinding stone may be too rough for it.

3

To remove errors along a horizontal or vertical line, you can use white correction tape. For other paper colors, you can purchase a liquid of a more suitable shade. After scanning a sheet of paper with correction tape applied, it will not be visible on the copy.

To correct an unsuccessful fragment, you can take a small piece of paper to cover it. You need to use clean paper of a suitable color to cut a scrap out of it. It is necessary in order to cover the place on the paper with an error. You can make appropriate corrections on top of the pasted piece of paper. Its edges should fit snugly to the sheet and not bend upward.

To remove errors along a horizontal or vertical line, you can use a white correction tape

The pasted piece of paper will be visible upon careful inspection. If you make a copy of the original, the corrections will be less noticeable. Trying to disguise blots from spilled ink may not be successful. You can try adding additional elements to the drawing, that is, a background or shading.

If you have to worry about someone needing to erase ink from a receipt or other document, you can use gel paste. It is difficult to choose a removal method for such a pen. To avoid accidentally removing ink from desired areas, you must use masking tape or paper.

4

You can use correction fluid to mask the ink. Despite the fact that it does not erase the ink, but only covers it, making it invisible, the use of corrector is common. This thick white liquid can be used to cover up any unwanted marks or errors in handwritten text. To apply the corrector, use a small brush with a sponge at the end.

Using a proofreader, you can cover up any unwanted blots and errors in handwritten text.

To correct ink marks, apply correction fluid and wait until it dries. After this, the product takes on the appearance of a crust or scales. Before removing ink from paper, you should check what consistency the correction fluid has. Immediately after application, the composition will be wet, so you must handle the paper carefully. Do not touch the brush from the bottle with correction fluid to other surfaces.

Correction fluid can only be used if the marking is barely noticeable. Choose only high quality white putty, otherwise it may turn into crumbs. The correction fluid should not be thick or clear. If after the first application the effect was not noticed, you can repeat it all over again, finally drying the sheet with the corrections.

5

If the drawing turns out to be damaged after accidentally drawing unnecessary lines, then you can add an ornament or additional decorations to it. As a result, the corrections will not be noticeable. They will look like the original design when creating the drawing.

Copying an ink image without an erroneous fragment is carried out if there are no blots or blots. This method is labor-intensive, but it is suitable if other methods have not given a positive effect. The drawing is finally completed on a new sheet of paper. This method eliminates noticeable corrections and additional marks. They will no longer be in the new picture.

To remove a small fragment of an erroneous recording, you can use the most ordinary razor blade

To prevent a sheet of paper from looking deformed, you can hold it under pressure for a while. You should first lay out the drawing with clean sheets, and then place it under a heavy flat object, for example, a book. The paper can be fed through the fax rollers. To level it, use a warm iron to iron the sheet.

To remove a small fragment of an erroneous recording, you can use a very ordinary razor blade. In this case, it is important to have a trained hand, otherwise there is a risk of ruining the sheet of paper completely. In any case, you should use this method by removing the top layer from the damaged section of paper. It is necessary to ensure that the structure of the sheet is not disturbed.

Before wiping the pen off the paper without leaving a trace, you can scratch the problem area with a razor blade. After this, you will need to take an eraser and rub it with pressure over the treated area several times. The “ruffled” surface of the sheet will need to be smoothed out with a flat, heavy object - an iron or blade. Unnecessary writing can be erased with a finger, which should first be moistened in water. To mask the recording, the top layer of paper must be gradually rolled up with your finger.

6

If an important document has been damaged as a result of unnecessary underlining, then it will be quite difficult to draw a line without certain skills. We remove blots from sheets or ink notes from the margins of books, following all the rules. This requires extreme care and caution.

If chemical compounds are used to remove ink, the most common remedy is a solution of vinegar and potassium permanganate

If chemical compounds are used to remove ink, the most common remedy is a solution of vinegar and potassium permanganate. Only 1 tsp is required. vinegar 70% concentration, in which potassium permanganate crystals should be dissolved in a small amount. Use this mixture to carefully remove pen marks. You can take a thin watercolor brush, and also place a clean sheet under the surface to be treated in advance.

The leaf may appear brown or purple due to the use of potassium permanganate. In this case, you will need to wait until it dries completely. Removal of brown stains is carried out using 3% hydrogen peroxide. This substance can be used separately to remove not too bright ink stains.

You can use cotton swabs or balls as a working tool. Instead of hydrogen peroxide, a solution of hydroperite is suitable: dissolve 2 tablets in 100 ml of water at room temperature. If the marks from the ink pen have not completely disappeared, all steps should be repeated again.

You can prepare the following composition:

• oxalic acid - 10 g;
• citric acid - 10 g;
• water - 1/2 cup.

After dissolving oxalic and citric acid in water, you should try to remove the ink with this composition. Another composition option for their removal is a solution containing:

• hydrochloric acid - 10 g;
• table salt - 10 g;
• water - 30 ml.

You need to take a glass with a hole through which you should slowly inject citric acid with a syringe. It should eat away at the ink. Soda or salt can be used as an absorbent. To remove colored ink, you can use a saturated solution of potassium permanganate. To prepare it you will need 50 ml distilled water at room temperature. Only a freshly prepared solution is active.

How to remove ink from paper (document) so that the mistake is not noticeable? I really need it!

Answers

3 0

7 (50998) 5 51 160 8 years

How to remove ink

Removing ink from paper is a delicate process. It requires concentration and calm. Let's look at this process using the example of a two in a diary. Naturally, it is not logical to correct a two to a five, so instead of a two, it would be necessary to put a four.
Let's get to work. It is difficult to prepare complex chemical reagents for high-quality removal of deuces at home. Therefore, we will use one of two methods: either chlorine or hydrogen peroxide with potassium permanganate.
First we try with chlorine. To do this, you can use any chlorine-containing liquid for household needs. The liquid should have a viscosity close to water and be translucent. Take a pipette and drop a drop of this liquid onto the glass. We take a match, dip it into a drop on the glass, this drop mostly remains on the tip of the match, transfer the liquid with the match to the diary paper far from the deuce (to test the reaction of the paper). We wait half an hour. If the paper does not turn yellow where the chlorine liquid was applied, then apply the liquid to the deuce. In 10% of cases the deuce has disappeared, in 20% the result is satisfactory - the outlines of the deuce will be barely visible, which can sometimes be removed with two strokes of the eraser, in 70% the result is unsatisfactory.
Then we try the second method.
We start by preparing 10% hydrogen peroxide; if you don’t have it, pharmacy 3% peroxide will do. Pipette. Peroxide on glass. Sprinkle 3-5 grams on the glass nearby. potassium permanganate. Using a match moistened with water, first transfer potassium permanganate onto the diary paper far from the deuce (for testing). Then use a second match to drip peroxide onto the potassium permanganate. Hiss. We wait half an hour. If the paper has not changed color, we perform the same operation with the deuce. The success rate is the same as with chlorine.
Do not experiment with important documents. If the deuce is written with gel or ink, then the methods described above can ruin the paper.

How to remove (remove, erase) pen ink, unnecessary notes, inscriptions, blots, stamps and seals from paper:

Recipe 1. Tools for removing / flattening written in ink, a regular fountain pen, and stamps.

To make the liquid, take 70% vinegar concentrate (about 1 teaspoon) and a small amount of potassium permanganate in crystalline form (at the tip of a knife). Everything is mixed, the liquid is ready for use.
Under the sheet from which you want to remove something, place a clean, white sheet of paper. Take a brush (the softer and thinner it is than her hair, the better), dip it into the prepared liquid and begin to move this brush over the inscription until it disappears. At this point the paper acquires a brownish tint; remove it with a piece of cotton wool soaked in hydrogen peroxide (all components are sold at the pharmacy).
Then, the area of ​​the wetted sheet must be ironed with a warm iron. To do this, soft matter is laid down, a clean, white sheet of paper is placed on it, and a sheet from which the inscription has been removed is placed on it and ironed (the surface of the iron must be clean, if there are black spots, then a clean white sheet is placed on top of the wet sheet and ironed) .
Note: This method removes inscriptions better from thin sheets; to remove from thick, dense sheets, it is advisable to use a sharpened match instead of a brush. Wrap a small piece of cotton wool around the sharpened tip (several of these brushes are made because they quickly break down), moisten them in liquid and carefully trace it with a back-and-forth movement along the inscription.
Everything else is done in the same way.

Recipe 2. Tools for mixing (erasing, removing, displaying) stamps, inscriptions, blots, etc.

Oxalic acid 10 g, citric acid 10 g, water 100 ml. - stir thoroughly.
The stamp or inscription is moistened with this solution with a soft brush 2-3 times, then moistened with clean water using a brush and the etched area is dried with a blotter.

Recipe 3. Tools for combining stamps, inscriptions, blots, etc.

Hydrochloric acid 10 g, table salt 10 g, water 30 ml. - stir and apply as the previous two products.

Method 4: Removing / flattening blue (purple, red, green) paste, fountain pen ink, stamp mastic.

You need to prepare two solutions:
Solution 1. Potassium permanganate (3-10 g) is added to distilled water (50 ml) at a temperature of 20-30°C in small portions and stirred until completely dissolved. After the solution becomes saturated and the next portion of potassium permanganate no longer dissolves, add glacial acetic acid (50 ml). The solution quickly loses its activity during storage. Prepare immediately before use.
Solution 2. Add 1-2 tablets of hydroperite to distilled water (100 ml) at a temperature of 20-30°C.
Application: Using a thin cotton swab on a glass rod or match, apply solution No. 1 with a light touch to the stain to be removed, starting from the center. DO NOT RUB. After 10-15 seconds the treatment can be repeated. The stain from solution No. 1 is discolored with solution No. 2.

Method 5: Removing / flattening black paste, ink, stamp mastic.

The difference from recipe 4 is that you first remove the first layer of black with a cotton swab soaked in alcohol, and then proceed in the same way as in the first recipe. When using the method on paper that has a colored protective grid or inscriptions in printing ink of all colors except black, in some cases the color of the dyes may change. It is recommended to carry out preliminary tests on a small area.

Method 6. Mixing ink and stamps.

Sodium sulfite or any other substance containing SO3 ion must be mixed with water. The gas released during this process with a sharp unpleasant odor returns the leaf to its original whiteness.

Recipes: how to remove ink stains.

1. They can be removed with a mixture of glycerin and ethyl alcohol (in equal proportions).
2. Fresh ink stains can be easily removed with warm fresh milk or curdled milk.

Method 1. Removing stamps from postage stamps.
When you send a letter and enclose an answer envelope in it, carefully rub the stamps or postal letters with paraffin (candle). When it is stamped at the post office, the stamp ink will remain on the paraffin. When this letter is returned to you, you will carefully scrape off the paraffin (with a sharp knife or fingernail). Cut out the stamp and soak it in a water bath (steam) or warm water so that the paraffin with the remaining traces of stamp ink comes off. Then dry the stamp, place it between two clean, white sheets of paper and iron it with a warm iron. And the brand is ready. You can stick it on the next envelope.

Method 2. Removing seals from postage stamps.
The whole operation is carried out similarly to the first method, only instead of paraffin, laundry soap (preferably white) is used. Rub the postage stamps with it, and when this letter with stamps is returned to you, you can easily remove the seal or stamp from the stamps using laundry bleach and a soft brush, carefully wiping off the stamp ink, then dip the stamp in boiling water, where it will separate from the stamp in a few seconds paper Then dry the stamps and use again with soap.

Method 3. Removing stamps and seals from postage stamps.
Postage stamps can be coated with a special layer, from which the stamp ink used to put postage stamps on postage stamps is easily wiped off.
The special layer consists of two parts:
1. Apply a thin layer of PVA glue (polyvinyl acetate emulsion) to the stamp and dry it.
2. Mix acetone and turpentine (1:2.5 ratio), drop castor oil into the mixture (1 drop per 5 ml), stir. Then put pieces of polystyrene foam into it, without stirring them, until you get a homogeneous thick mass. When the liquid mixture no longer remains on the surface of the thick viscous solution, the composition must be mixed and applied in a thin layer to the prepared stamps. After drying, they can be glued to envelopes and sent by mail. When you need to remove the stamp from the stamp, just wipe it with your finger, after breathing on it, or with a damp cotton swab.
Notes: If you do not apply a layer of PVA glue to the stamp, but immediately apply a second layer, then acetone and turpentine may blur the image on the stamp.
If castor oil is not added to the mixture of acetone and turpentine at the beginning, then the second layer will turn out brittle and may crack during stamping; stamp ink gets into the cracks during stamping and will not be removed by simple means.
The best substance for preparing the second composition is, as experience shows, white synthetic porous packaging for eggs.
The most convenient tool for coating stamps is an old-style dental spatula.
When using stamps, do not put protected stamps together with unprotected ones on the same envelope, because when compared closely they are slightly different from each other.
Once you learn how to apply the second coat in one precise motion, then a layer of PVA will not be necessary.
Note: Composition 2 “compacts” during storage, that is, it separates. Therefore, it is better to use it immediately or a few hours after preparation. Next, take hydrogen peroxide (also sold at the pharmacy), moisten the cotton wool and carefully soak the pink stains that remain from the erased inscription. And voila, no traces of the inscription remain! If we are talking about a purchase and sale agreement, then the certification of each signature was about 12 lats.

Students most often face the problem of how to erase pen from paper without leaving marks. Handwritten works are time consuming. Sometimes one word can be fatal, and then the question arises of how to remove ink from paper. Today there are several ways to solve this problem.

Sometimes one word can be fatal, and then the question arises of how to remove ink from paper

How to erase ink from paper

The most effective way is acetone. Of course, it is not recommended to use the solution in its pure form, as it can ruin the paper. You must use nail polish remover. It is less concentrated than acetone. Such a simple tool can be found in any store, but it must be used correctly so as not to spoil the rest of the written material.

First, take a cotton swab and dip it in the liquid. Then apply the product to the problem area and hold for several minutes. Then use the same cotton swab to gently wipe off the ink. This must be done extremely carefully. After this, blot the area where the liquid was applied with a paper napkin.

Few people know how to erase ink from paper using hydrogen peroxide. However, this tool allows you to easily get rid of an extra letter or word without damaging the paper. You will need a hydrogen peroxide solution. If you have hydroperite tablets, you can use them. For 50 ml of water you will need 4 pieces.

The most effective way is acetone. Of course, it is not recommended to use the solution in its pure form, as it can ruin the paper

Use the resulting solution to treat the inscription that needs to be erased, and carefully go over it with a cotton pad or swab. You should not do this too intensely, as this may damage the paper web. If the procedure turns out to be ineffective, it is recommended to repeat it after some time.

How to properly clean a dishwasher at home

Many schoolchildren are faced with the question of how to erase a bad mark in their diary without their parents noticing. There is a special trick for this. It is necessary to prepare a glass dish and put potassium permanganate there on the tip of a knife. Then pour less than 0.5 tsp. acetic acid. Mix both ingredients carefully. And apply, preferably with a thin brush, for assessment. Then soak a cotton pad in hydrogen peroxide and gently wipe off.

To prevent ink from remaining on a sheet of paper, you can also use toothpaste

You should not be afraid of the bright shade of the liquid. Peroxide will easily remove it. You can also erase a bad mark from your diary using alcohol. To do this, you will need additional glycerin, which should be slightly heated. Both components must be mixed in equal quantities and very carefully applied to the mark or note. It is advisable to do this along the contour.

How to remove ink from paper (video)

Additional methods

How to remove a bad grade from a diary, how to erase a remark - this is interesting for almost all students to know. For such purposes, you can prepare another alcohol-based solution. You will need 10 g of soda powder. It must be placed in a glass container. Then pour in 200 ml of alcohol and 100 ml of water. All ingredients should be mixed and applied to the ink that needs to be erased using a cotton swab.

Score 2 can also be eliminated using the old-fashioned method. You need to take a razor blade. The spicier the better (but be careful!). Then erase the mark by lightly scraping the paper. The main thing is not to overdo it. The second time, you should go over what you have written very carefully so as not to damage the paper.

How to remove a bad grade from a diary, how to erase a remark - this is interesting for almost all students to know

You can erase a note from the teacher using a mixture of 2 acids: oxalic and citric. Before removing the ink, you must mix both components in equal quantities and add water to obtain a 1:10 solution. This composition removes ink very effectively. To do this, the product is applied to the inscription that needs to be removed in two layers. After this, the treated area should be moistened with water and blotted with a napkin.

In the era of computerization and electronic document management, paper media continues to be used. And ways to erase pen from paper without leaving traces help students, schoolchildren, secretaries, and office workers save time on reworking papers with outdated or incorrect data, typos or clerical errors.

On white paper, errors can be covered up with a proofreader, but for colored forms this method is unacceptable. Using publicly available tools, you can correct typos at home as accurately as possible, as if they never happened, and save a damaged document.

Important! There are documents in which erasing ink and correcting information is undesirable and even illegal. Corrections in a passport or birth certificate are regarded as falsification of documents, and a sick leave certificate with corrections is considered invalid.

Chemical compositions

To completely remove traces of ink from a sheet of paper, choose the optimal method for specific conditions. Methods using chemicals and compounds that many housewives have are suitable for the home.

Acetone

This solvent copes with many contaminants of various origins; pen ink also lends itself to it. Acetone cannot be used in its pure form - the solvent will corrode both the pigment and the paper. Acetone-containing liquids are suitable, or, alternatively, nail polish remover. It is in every home where girls or women live, it can be bought in almost any store, and it is inexpensive.

We remove traces of pens, working correctly:

1. Slowly, carefully and in small quantities (using a cotton swab, pipette, toothpick) apply the liquid to the problem area.
2. Using a cotton pad or soft cloth, carefully blot the liquid from the sheet. Movements are made in a vertical plane so as not to stain the sheet.
3. If ink contamination remains, repeat the procedure.

Advice! For complete cleansing, the entire sheet is immersed in liquid and then dried in a room with good ventilation.

Hydrogen peroxide

A cotton swab or the end of a rolled-up cotton pad is moistened in peroxide and a thin layer of liquid is applied to the inscription. Then the liquid with the ink dissolved in it is removed with a soaking motion using a soft cloth. The sheet of paper is dried after the procedure.

Advice! Hydrogen peroxide can be replaced with hydroperite.

Product with ethyl alcohol

A composition of ethyl alcohol and glycerin is prepared by combining the substances in equal parts. The resulting product is applied with a cotton swab, following the contour of the letters or numbers being erased.

Another composition based on ethyl alcohol is used: 200 g of ethyl alcohol, 10 g of baking soda, 100 ml of water. It responds well to marks from a ballpoint pen.

Old method using "Whiteness"

To remove pen marks other than Whiteness, you will need nail polish remover. This method of removing ink has proven to be simple and effective.

First, the text or blot from a pen is treated with “Whiteness” - a cotton swab is moistened in the liquid and rubbed over the dirt. After the wet area has dried a little, it is treated with an acetone-containing liquid (nail polish remover) using a cotton swab. You need to moisten the mark from a ballpoint pen using rubbing movements in several passes.

As a result, the place where the work was carried out becomes blank paper. Because it is wet, it is dried out.

Potassium permanganate with vinegar

Pen paste that has leaked onto paper or unnecessary notes can be removed using a method popular on the Internet using vinegar essence and potassium permanganate.

In a small glass container, the ingredients are mixed in small quantities. So much potassium permanganate is used that the liquid, after dissolving the powder, acquires a garnet color.

Procedure:

1. The resulting composition, using a cotton swab, is applied to the place with a typo or other information that needs to be removed.
2. Leave for 30 seconds.
3. Hydrogen peroxide is applied on top, which dissolves the remaining contamination and removes the reddish tone of the paper from potassium permanganate.
4. Iron a damp sheet of paper, covering the wet area with a moisture-absorbing cloth. As a result, the paper becomes clean and smooth.

Toothpaste

Using toothpaste to remove ballpoint marks is safe and effective. The paste is slowly rubbed into the paper, and the residue is removed with a damp cloth.

Solar alternative

Almost all dyes fade when exposed to direct sunlight. Ink pigments are no exception. If the paper is placed in a sunny place, the ink will fade and become discolored, and to avoid getting a completely clean and darkened sheet, cover the necessary information and free areas with foil or paper.

Mechanical methods

Under mechanical influence, the ink of a variety of pens becomes invisible: gel, ballpoint, capillary. The method does not involve dissolving the ink, but rather removing blots or erroneous information by cutting off the top layer of paper.

Advice! In order not to rub the document into holes, it is advisable to experiment on an unnecessary sheet.

Eraser and blade

The ink is wiped off with the corner of the eraser so as not to affect the necessary information. Adjusting the blade along the contour of text characters is more accurate. The layer of paper is scraped off using the corner of the blade, or cut off to give the metal an arc shape. The roughness that appears is removed by pressing the irregularities with something smooth, for example, a nail plate.

Medical adhesive plaster

To reduce unnecessary words, letters, numbers, a cut piece of adhesive tape is glued on top. Its size and shape are adapted to the location with erroneous information. The glued piece is pressed with force and carefully, carefully removed from the paper. A top layer of paper with ink remains on the surface of the removed patch.

Advice! To avoid leaving colored spots on the paper, you need to use a white-based adhesive plaster.

Abrasive paper

Sometimes the ink is scraped off with fine-grit sandpaper. Working with it pointwise, it is possible to remove even small letters and dashes.

When the ink is colored

Colored inscriptions are displayed using the following means:

1. Composition of oxalic and citric acid. The ingredients are taken 1 part at a time and diluted with 10 parts of water. The composition is applied with a thin brush along the contour of the symbols. You can immediately see how the ink discolors and the notes disappear. Thanks to the precise application of the product, it is possible to effectively remove the error and easily correct the number in the document.
2. Chlorine bleach (for example, "White"). It is applied with a cotton swab dipped in the product. Press the wet area with a dry cloth to absorb moisture; if necessary, iron the top with a warm iron.
3. A solution with salt. It is prepared by diluting it in 3 tbsp. l. water 2 tsp. salt and adding 10 ml of hydrochloric acid. The composition turns out to be caustic and toxic - it must be used with extreme caution. The product is applied to the problem area with a cotton swab. After the ink disappears, the processed part of the sheet is blotted with a damp sponge.
4. Vinegar. It is applied to paper, and then, when the spice dissolves the ink, the wet mark is blotted with a napkin or cotton pad soaked in water.

Office work, secretarial work, study and teaching are closely related to paper and hand writing. In a hurry or by mistake, entries may need to be corrected or deleted. Ink is decolorized without harming the paper using chemical means; mechanical erasing methods are used on plain sheets. But they all require extreme caution and accuracy, so it’s worth assessing in advance whether it would be easier to simply rewrite the document or work.